CYCOLOY™ C1000 Resin. General Purpose Grade for Wide Applications

Best PC/ABS for Low Heat Products & Balance Processing & Performance

CYCOLOY™ C1000 PC/ABS Resin is a General Purpose engineering Thermoplastic developed to provide a practical balance between Processability and Functional Performance. This PC/ABS Blend is intended for wide application use where Low Heat Requirements, Manufacturing efficiency, and material Consistency are Primary selection criteria.

Processing Behavior of CYCOLOY™ C1000 PC/ABS Resin emphasizes ease of molding, supporting Stable Flow and Predictable Part Formation across a range of Standard Processing Conditions. This Characteristic makes the material well suited for High Volume Manufacturing Environments where Efficiency and Repeatability are Important.

Mechanical and Dimensional performance of CYCOLOY™ C1000 PC/ABS Resin is made to meet the needs of Low Heat applications without excess specification. The balanced property profile supports reliable Part Integrity while avoiding Over Engineering in designs where extreme thermal or Structural Demands are not required.

Application Flexibility is a Key Attribute of CYCOLOY™ C1000 PC/ABS Resin, allowing use across a broad range of General‑Purpose Products. This Versatility supports Designers and Manufacturers seeking a Single material Solution for Multiple Low Heat use cases.

Flammability Classification of CYCOLOY™ C1000 PC/ABS Resin is defined by its UL Performance Rating. CYCOLOY™ C1000 is UL94‑HB Rated at 1.00 mm ~ 3.00 mm, supporting use in products where Baseline Flammability Requirements apply without the need for Flame‑Retardant Formulations.

Environmental and Market alignment is addressed through the ROHS Compliant Status of CYCOLOY™ C1000 PC/ABS Resin, enabling Application in Global Markets. This Compliance completes the material profile by aligning Processing Simplicity, General‑Purpose Performance, and Regulatory Compatibility.

Notes :

CYCOLOY™ C1000 PC/ABS Resin
General Puurpose Grade
Balance Performance
UL94‑HB Rated at 1.00 mm ~ 3.00 mm
ROHS Compliant

CYCOLOY™ C1000 Resin has 0.50 ~ 0.70 Shrinkage, Flow, 3.2 mm. %

Material HDT, 1.82 MPa, ASTM A648, °C

N/A

Vicat Softening Temperature Rate

CYCOLOY™ C1000 , Vicat Softening Temperature rate , B120 = 115

Material MFI / Melt Flow Rate

Melt Flow Rate, 260°C/5.0 kgf = 15

Material Melt Volume Rate, MVR

N/A

Material Flexural Modulus

CYCOLOY™ C1000 Flexural Modulus, ISO 178, 2.0 mm/min = 2300 Mpa

CYCOLOY Main Page

Disclaimer

Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021

SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.