CYCOLOY™ MC8800 Resin. Low CTE PC/ABS with High Impact Strength.

Best for Automotive Exterior, Ductile and High Heat Resistance

CYCOLOY™ MC8800 PC/ABS Resin is a Low‑Coefficient‑of‑Thermal‑Expansion Engineering Thermoplastic developed for Automotive Exterior applications requiring Dimensional Stability under Thermal Exposure. This PC/ABS Blend is designed to maintain Shape and alignment when subjected to Temperature Variation, supporting consistent performance in Exterior Environments.

Thermal Expansion Control is a Key Attribute of CYCOLOY™ MC8800 PC/ABS Resin, reducing dimensional change during Heating and Cooling cycles. This Low CTE behaviour helps maintain tight panel fit, surface alignment, and part geometry in automotive exterior components exposed to sunlight and environmental temperature variation.

Mechanical Performance of CYCOLOY™ MC8800 PC/ABS Resin includes High Impact Strength, supporting resistance to mechanical stress during assembly and service. The material retains Ductility, enabling components to Absorb Impact without Cracking while maintaining structural integrity.

CYCOLOY™ MC8800 PC/ABS Resin Thermal Capability support use in Higher Heat Exterior Conditions, allowing parts to withstand elevated temperatures without Excessive Deformation. This Heat Resistance contributes to long‑term durability in demanding outdoor applications.

Processing behaviour of CYCOLOY™ MC8800 PC/ABS Resin is optimized for Injection Molding, enabling controlled material flow and consistent part formation. This Processing Stability support reliable manufacture of large or complex exterior components.

Application suitability of CYCOLOY™ MC8800 PC/ABS Resin focuses on Automotive Exterior Parts where Low Thermal Expansion, Impact Resistance, and Heat Performance must be achieved together, providing a balanced solution for demanding design requirements.

Environmental and regulatory alignment is addressed through the ROHS compliant status of CYCOLOY™ MC8800 PC/ABS Resin, enabling integration into global automotive platforms where dimensional stability, durability, and compliance are required.

Notes :

CYCOLOY™ MC8800 PC/ABS Resin
Low CTE
High Heat Strength
RoHS Compliant

CYCOLOY™ MC8800 Resin has 0.4 ~ 0.6 Shrinkage, Flow, 3.2 mm. %

Material HDT, 1.82 MPa, ASTM A648, °C

3.2 mm, unannealed @ 120

Vicat Softening Temperature Rate

CYCOLOY™ MC8800 , Vicat Softening Temperature rate , B50 = 117

Material MFI / Melt Flow Rate

Melt Flow Rate, 260°C/5.0 kgf = 10

Material Melt Volume Rate, MVR

N/A

Material Flexural Modulus

CYCOLOY™ MC8800 Flexural Modulus, ASTM D790, 1.3 mm/min = 2960 Mpa

CYCOLOY Main Page

Disclaimer

Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021

SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.