BRINGING THE RIGHT MATERIAL & BEST SERVICES IN SOUTH EAST ASIA
Thailand Office : +66 88 874 7437
Malaysia Office : +6012 283 6969
Indonesia Office : +62 818 0402 0119
Vietnam Office : +84 934 036 679
Philippines Office : +63 917 567 4188
India Office : +91 988 439 6812
ELCRES™ DMX6034 Polycarbonate Hard Resin. Custom Color, UV Stabilized
UV Stabilized, Improved Scratch Resistance & Impact Modified
LNP™ ELCRES™ DMX6034 Resin is a Balance Scratch Resistance Good Ductility Polycarbonate. Copolymer ELCRES with Good Surface Hardness and improved Scratch Resistance
The Material is Available in Opaque Color and added UV Stabilizer
LNP™ ELCRES™ DMX6034 Resin has Balance Ductility and Chemical Resistance
The Grade is from the LNP™ ELCRES™ Copolymer DMX Series, which offers a Significantly Improved Surface Hardness 5-Times Higher Pencil Hardness than Standard PC
Independent Laboratory Tests, using the Pencil Hardness (1 kgf) Standard, these Materials Achieved an H Rating Compared to a Much Lower 2B Rating for Ordinary PC – Equivalent to up to Five Times the Hardness of the Standard Material.
The DMX Resins even Surpassed Painted Acrylonitrile Butadiene Styrene (ABS), PC/ABS, and other Painted Resins, which only Achieved a Mid-range F Rating. Further, if the ELCRES DMX Resin Grades are Hard-Coated with Silicone or Acrylic, their Pencil Hardness Increases to 3H.
Eliminating the Need for Secondary Coating Operations, which may Provide Several Important Benefits to Manufacturers:
- Lower Costs by Avoiding the Purchase of Coating Materials and Equipment
- Reduced Cycle Time by Cutting Out a Secondary Processing Step and Avoid Environmental Impact from Volatile Organic Compounds (VOCs) Released into the Atmosphere from the Coating Process
ELCRES™ DMX6034 is a Opaque Color ROHS Compliance Polycarbonate Resin
Material HDT, 1.82 MPa, ASTM A648, °C
3.2 mm, unannealed 114
Vicat Softening Temperature Rate
Vicat Softening Temperature Rate, B50 = 134
Material MFI / Melt Flow Rate
Melt Flow Rate, 300°C/1.2 kgf = 10
Material Melt Volume Rate, MVR
Melt Volume Rate, 300°C/1.2 kg = 9
Material Flexural Modulus
Flexural Modulus, ISO 178, 2 mm/min, MPa = 2130
ELCRES™ DMX6034 Resin are Non UL94 Listed
Disclaimer
Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021
SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Elcrin, Elcres, Lexan, Noryl, Ultem, Xenoy, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.