LEXAN™ DMX1435 Transparent Polycarbonate Resin. Copolymer Harder Resin

Standard Flow, added UV Stabilizer. Harder Surface Scratch Resistance

LEXAN™ DMX1435 Resin is a Copolymer Harder Resin Polycarbonate. Copolymer LEXAN with Improved Surface Hardness for Better Scratch Resistance

The Material is Available in Limited Transparent Clear

LEXAN™ DMX1435 Resin has added UV Stabilizer. Standard Flow Rate and Improved Dielectric Performance

The Grade is from the LEXAN™ Copolymer DMX Series, which offers a Significantly Improved Surface Hardness 5-Times Higher Pencil Hardness than Standard PC

Independent Laboratory Tests, using the Pencil Hardness (1 kgf) Standard, these Materials Achieved an H Rating Compared to a Much Lower 2B Rating for Ordinary PC – Equivalent to up to Five Times the Hardness of the Standard Material. The GE Resins even Surpassed Painted Acrylonitrile Butadiene Styrene (ABS), PC/ABS, and other Painted Resins, which only Achieved a Mid-range F Rating. Further, if the LEXAN DMX Resin Grades are Hard-Coated with Silicone or Acrylic, their Pencil Hardness Increases to 3H.

Eliminating the Need for Secondary Coating Operations, which may Provide Several Important Benefits to Manufacturers:

- Lower Costs by Avoiding the Purchase of Coating Materials and Equipment
- Reduced Cycle Time by Cutting Out a Secondary Processing Step and Avoid Environmental Impact from Volatile Organic Compounds (VOCs) Released into the Atmosphere from the Coating Process

LEXAN™ DMX1435 is a Transparent Clear ROHS Compliance Polycarbonate Resin

LEXAN™ DMX1435 Resin HDT, 1.82 MPa, ASTM A648, 3.2 mm, unannealed is at 119°C

Vicat Softening Temperature of LEXAN™ Polycarbonate DMX1435 Resin

Vicat Softening Temperature Rate, B50 = 139

Material MFI / Melt Flow Rate

Melt Flow Rate, 300°C/1.2 kgf = 14.5

Material Melt Volume Rate, MVR

Melt Volume Rate, 300°C/1.2 kg = 13

Material Flexural Modulus

Flexural Modulus, ISO 178, 2.0 mm/min, MPa = 2450

LEXAN™ DMX1435 Copolymer Resin has 0.5 ~ 0.8 Shrinkage, Flow, 3.2 mm. %

LEXAN™ DMX1435 Polycarbonate Resin are UL94 - HB@ 1.0 mm ~ 3.0 mm

LEXAN COPOLYMER Page

Disclaimer

Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021

SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.