BRINGING THE RIGHT MATERIAL & BEST SERVICES IN SOUTH EAST ASIA
Thailand Office : +66 88 874 7437
Malaysia Office : +6012 283 6969
Indonesia Office : +62 818 0402 0119
Vietnam Office : +84 934 036 679
Philippines Office : +63 917 567 4188
India Office : +91 988 439 6812
High Flow, Low Water Absorption, Chemical Resistance & Heat Resistance
NORYL GTX™ series, GTX9500 PPE + PA is a Non-Reinforced Blend of Polyphenylene Ether (PPE) + Polyamide (PA), This Grade Absorbed 21% Less Moisture at Equilibrium than PA66, and 58% less than PA6.
It Features Excellent Chemical Resistance, Good Impact Strength, Surfaces Appearance, Excellent Processability, and Long Term Dimensional Stability. It Retains a Better Balance of Mechanical Properties when Exposed to Humidity and Heat Typical of Automotive Under the Hood Environments, than Polyamide Resins (PA66 and PA6) and Comparable High Flow, High Temperature Performance
NORYL GTX™ series, GTX9500 PPE + PA Resin is an Excellent Candidate for Various Applications in the Automotive and Electronics Industries.
This Resin is from the Family of NORYL GTX™, is A Blend of Polyamide (PA) and Polyphenylene Ether Polymer (PPE) Technology. Unique Long Term Stability, Low Moisture Absorption, Good Stiffness, Strength & Impact Resistance of PPE.
Chemical Resistance, Good Flow & Toughness of PA or Unique Various Resistance Polyphenylene Sulfide, PPS
NORYL GTX Resins offer a Balance of Mechanical and Chemical Properties and may be Suitable for a Wide Variety of Applications
As a Blend NORYL GTX™ Resin offers
- Chemical Resistance
- Paintable Grades Available
- Electrical Properties - Conductive Grade Available
- Strength & Stiffness - Virtually Unaffected by Humidity, Impact Strength
- Creep Resistance - Elevated Temperature, Improved with Added Filler
- Low Shrinkage - Excellent Control in Dimension
- Impact Resistance to Crash Performance
NORYL GTX9500 PPE + PA has 1.771 Shrinkage, Flow, 3.2 mm. %
Material HDT, 1.82 MPa, ASTM A648, °C
3.2 mm, unannealed 123
Vicat Softening Temperature Rate
Vicat Softening Temperature rate , B50 = 152
Material MFI / Melt Flow Rate
Melt Flow Rate, 280°C/2.16 kgf = 28
Material Melt Volume Rate, MVR
N/A
Material Flexural Modulus
2305
NORYL™ GTX9500 are Non UL Rated
Disclaimer
Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021
SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.