NORYL™ GFN30 Outdoor 30% Glass Reinforced PPE + HIPS Unique Blend

General Purpose Resin for Outdoor Applications. For Asia Market

NORYL™ GFN30 PPE + HIPS Resin Is an Outdoor Oriented, Glass Reinforced engineering Thermoplastic designed for General Purpose applications requiring increased structural support and Environmental Stability. With 30% Glass Reinforcement in a PPE + PS Resin System, This Grade supports Outdoor use cases where Dimensional Control and Resistance to Environmental Exposure Are Key Design Drivers.

Higher Reinforcement content in NORYL™ GFN30 PPE + HIPS Resin contributes to enhanced Stiffness and Improved Shape Retention Compared to Lower Glass Filled Variants. This Structural Improvement supports components subjected to Mechanical Load or Outdoor Stress while maintaining a practical Balance between Strength and Part Manufacturability.

Performance in Moisture Exposed Conditions Is supported by the Hydrolytic Stability of NORYL™ GFN30 PPE + HIPS Resin, helping reduce property Degradation over Time. Low Warpage behavior enables Molded Parts to maintain Dimensional accuracy in Outdoor Environments where Temperature and Humidity Fluctuations can Influence Long‑Term Fit.

Design Efficiency is improved through the Low Specific Gravity of NORYL™ GFN30 PPE + HIPS Resin, allowing Structural Performance Gains without Excess Weight increase. This Characteristic supports Outdoor Component Design where Weight Control, Durability, and Structural Consistency must be balanced within a General engineering Framework.

Baseline Flammability requirements are addressed by the UL Performance Classification Associated With NORYL™ GFN30 PPE + HIPS Resin. NORYL™ GFN30 are UL94 ‑ HB, 1.5 mm ~ 3.00 mm Rated, supporting use in applications where Standard Flame Performance is required without Dedicated Flame Retardant Formulations.

Environmental and Regulatory Alignment Is supported by the ROHS Compliant Status of NORYL™ GFN30 PPE + HIPS Resin, enabling Application in Products Targeting Global Markets. This Compliance Complements the Material’s Outdoor Stability, Reinforced Structure, and Long‑Term Dimensional Reliability.

Notes :

NORYL™ GFN30 PPE + HIPS Resin
30% Glass Fiber Reinforced
Available on in Asia Market
Outdoor Applications
Hydrolytic Stability
ROHS Compliant

NORYL GFN30 PPE + HIPS has 0.1 ~ 0.4 Shrinkage, Flow, 3.2 mm. %

Material HDT, 1.82 MPa, ASTM A648, °C

3.2 mm, unannealed 147

Vicat Softening Temperature Rate

Vicat Softening Temperature Rate, B50 = 147

Material MFI / Melt Flow Rate

Melt Flow Rate, 280°C/5.0 kgf = 3.2

Material Melt Volume Rate, MVR

Melt Volume Rate, 280°C/5.0 kgf = 2

Material Flexural Modulus

6800

NORYL™ GFN30 are UL94 - HB, 1.5 mm ~ 3.00 mm Rated

NORYL Main Page

Disclaimer

Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021

SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.