ULTEM™ 2110. Easy Flow formulated with 10% Glass Reinforced PEI Resin

Greater Rigidity. Improved Dimensional Stability vs ULTEM 1000 Series

ULTEM™ 2110 PEI Resin is a High-Performance Engineering Thermoplastic reinforced with 10% Glass Fiber, designed for applications requiring improved Flow, Enhanced Rigidity, and reliable High-Temperature Performance. With a Glass Transition Temperature (Tg) of 217°C, ULTEM™ 2110 PEI Resin maintains Structural Integrity under demanding Thermal Conditions, making it suitable for advanced Industrial and Electrical Environments.

The Glass-Reinforced PEI Structure in ULTEM™ 2110 PEI Resin provides Increased Stiffness, Higher Modulus, and improved Dimensional Stability, allowing components to withstand Mechanical Loads while maintaining Tight Tolerances. This optimized formulation reduces Warpage and enhances Part Consistency compared to Standard Grades, supporting Precision Applications where Accuracy and Stability remain Critical Requirements.

ULTEM™ 2110 PEI Resin offers improved Flow Characteristics compared to ULTEM™ 2100 and 1000 Series, enabling easier Processing and the production of Complex or Thin-Walled Components without compromising Mechanical Performance. This combination of Reinforcement and Flow Improvement allows ULTEM™ 2110 PEI Resin to deliver both Manufacturability and Structural Strength in demanding Production Environments.

Inherent Flame Retardant Properties allow ULTEM™ 2110 PEI Resin to achieve UL94 V0 Ratedfrom 0.41 mm to 3.00 mm without Halogenated Additives. This ensures Safe and reliable Performance in Electrical Components, Industrial Systems, and Applications requiring Flame Resistance and Safety Compliance.

High Strength and Rigidity at Elevated Temperatures, combined with Long-Term Thermal Stability, enable ULTEM™ 2110 PEI Resin to maintain consistent Performance under Continuous Use Conditions. Compared to Lower-Reinforced or Unreinforced Grades, ULTEM™ 2110 PEI Resin provides improved Dimensional Control and Mechanical Reliability in High-Load and High-Temperature Environments.

As part of the ULTEM™ 2000 Series, ULTEM™ 2110 PEI Resin offers Better Rigidity and Dimensional Stability compared to the ULTEM™ 1000 Series, while also delivering Lower Warpage and improved Process Efficiency. These characteristics make ULTEM™ 2110 PEI Resin a preferred Material for Structural and Precision-Molded Components.

ULTEM™ 2110 PEI Resin is available in Opaque Colors, supporting Applications where Mechanical Performance, Surface Definition, and Dimensional Accuracy are prioritized over Transparency.

Typical Applications for ULTEM™ 2110 PEI Resin include Electrical Components, Industrial Parts, Housings, and Structural Applications, where High Heat Resistance, Dimensional Control, and Processability must be maintained. ULTEM™ 2110 PEI Resin is also RoHS Compliant, supporting Environmentally Responsible Material Selection while delivering Reinforced High-Performance Characteristics.

Notes:

ULTEM™ 2110 PEI Resin
10% Glass Reinforced
Easy Flow Formulated
UL94 V0 Rated
RoHS Compliant

ULTEM™ 2110 PEI Resin has 0.40 ~ 0.60 Shrinkage, Flow, 3.2 mm. %

Material HDT, 1.82 MPa, ASTM A648, °C

6.4 mm, unannealed 207

Vicat Softening Temperature Rate

N/a

Material MFI / Melt Flow Rate

Melt flow Rate, 337°C/6.6 kgf = 11.3

Material Melt Volume Rate, MVR

N/a

Material Flexural Modulus

4500

ULTEM™ 2110 are UL94 - V0, 0.41 mm ~ 3.00 mm Rated

ULTEM Main Page

Disclaimer

Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021

SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.