ULTEM™ 2120. High Flow Formulated with 10% Glass Reinforced PEI Resin

excellent Dimension Stability, Strength, Stiffness & Creep Resistance

ULTEM™ 2120 PEI Resin, with 10% Glass Reinforced Polyetherimide is engineered to deliver reliable Strength and Dimensional Control in applications exposed to Heat and Mechanical Stress over extended Periods.

the ULTEM™ 2120 PEI Resin combines Reinforcement with a High Flow formulation, making it easier to process than Traditional Filled High Temperature Materials. Complex Geometries can be filled more effectively. Cycle stability improves during Molding, especially in Thin or Intricate Parts.

the Glass Reinforcement plays a critical role. ULTEM™ 2120 PEI Resin offers enhanced Stiffness and Strength, allowing components to resist deformation under sustained Load. This is supported by Strong Creep Resistance, which helps parts maintain Shape even during Long Term Mechanical Stress.

Thermal Performance remains a Foundation. with a Glass Transition Temperature of approximately 217 °C, ULTEM™ 2120 PEI Resin retains Structural Integrity in High Temperature Environments. Mechanical properties remain Stable where standard Plastics would Gradually Weaken.

ULTEM™ 2120 PEI Resin dimensional accuracy is another advantage. components Molded from show minimal Warpage and Stable Tolerances. This makes the material well suited for Precision applications where consistency over time is critical.

In Terms of Safety Performance, ULTEM™ 2120 PEI Resin is classified as UL94 V0, 0.50 mm ~ 3.00 mm Rated, allowing use in applications that require reliable Flame Resistance at Thin Wall Sections.

Typical uses include Structural Housings, Electrical components, High Temperature Connectors, and Load Bearing Assemblies, where Stiffness, Creep Resistance, and Thermal stability must Work Together.

Selecting ULTEM™ 2120 PEI Resin also reflects a Responsible material Decision. Its RoHS Compliant formulation support Environmentally Conscious Design while maintaining Advanced Engineering Performance.

Notes :

ULTEM™ 2120 PEI Resin
10% Glass Reinforced
UL94 Rated
RoHS Compliant

ULTEM™ 2120 PEI Resin has 0.3 ~ 0.5 Shrinkage, Flow, 3.2 mm. %

Material HDT, 1.82 MPa, ASTM A648, °C

N/a

Vicat Softening Temperature Rate

Vicat Softening Temperature rate , B50 = 215

Material MFI / Melt Flow Rate

Melt flow Rate, 337°C/6.7 kgf = 20

Material Melt Volume Rate, MVR

Melt Volume Rate, 337°C/6.7 kgf = 12

Material Flexural Modulus

4920

ULTEM™ 2120 are UL94 - V0, 0.50 mm ~ 3.00 mm Rated

ULTEM Main Page

Disclaimer

Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021

SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.