ULTEM™ 2210F 20% Glass Reinforced Food Contact Compliant PEI Resin

Greater Rigidity. Easy Flow, FDA NSF 5.1 Listed & WRAS Certified

applications Involving Water, Food Contact, and Structural reliability require Materials that meet Multiple Standards at Once. ULTEM™ 2210F PEI Resin is developed to address this need, Combining 20% Glass Fiber Reinforcement with Certified Compliance for Regulated Environments.

ULTEM™ 2210F PEI Resin delivers enhanced Rigidity through Glass Reinforcement. Parts maintain Shape under Load and during Long Service Cycles. Dimensional Control remains Stable even in applications exposed to Moisture or Thermal Variation.

Flow Performance has been optimized for Processing. ULTEM™ 2210F PEI Resin Fills Molds more efficiently than Traditional Reinforced PEI Grades. Complex Geometries can be produced with better Consistency, supporting reliable manufacturing Outcomes.

ULTEM™ 2210F PEI Resin meets U.S. FDA and EU Food contact Requirements, while also Holding NSF 51 Listing and WRAS Certification. These Approvals make it suitable for Systems Involving Potable Water, Food Processing, and Regulated Fluid Environments.

Thermal capability remains consistent with the PEI Platform. ULTEM™ 2210F PEI Resin maintains Performance at a Glass Transition Temperature of approximately 217 °C, allowing components to retain Strength under Elevated Temperature exposure.

the material is inherently Flame Retardant and achieves UL94-V0 Ratedfrom 0.41 mm to 3.00 mm, supporting use in applications that require High Fire Performance at Thinner Sections.
ULTEM™ 2210F PEI Resin is available in Opaque Recognized Colors, allowing flexibility in System Design while maintaining Compliance and Mechanical Performance.

Typical applications include Food contact components, Water System Parts, Beverage Equipment, Fluid Handling Systems, and Structural Assemblies, where Compliance, Rigidity, and Processing Performance must Work Together.

use of ULTEM™ 2210F PEI Resin also support Responsible material selection through RoHS alignment, helping meet Environmental Expectations alongside Engineering Requirements.

Notes:

ULTEM™ 2210F 20% PEI Resin
20% Glass Reinforced
Food Contact Compliant
Easy Flow
FDA NSF 5.1 Listed & WRAS Certified
UL94 Rated
RoHS Compliant

ULTEM™ 2210F PEI Resin has 0.30 ~ 0.50 Shrinkage, Flow, 3.2 mm. %

Material HDT, 1.82 MPa, ASTM A648, °C

N/a

Vicat Softening Temperature Rate

Vicat Softening Temperature rate , B50 = 210

Material MFI / Melt Flow Rate

N/a

Material Melt Volume Rate, MVR

Melt Volume Rate, 360°C/5.0 kgf = 10

Material Flexural Modulus

6500

ULTEM™ 2210F are UL94 - V0, 0.41 mm ~ 3.00 mm Rated

ULTEM Main Page

Disclaimer

Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021

SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.