ULTEM™ 2210R with 20% Glass Reinforced PEI Resin. Added Mold Release

Greater Rigidity. Improved Dimensional Stability and Improved Fow

ULTEM™ 2210R PEI Resin is a High-Performance Engineering Thermoplastic reinforced with 20% Glass Fiber, developed for Applications requiring a strong balance of Rigidity, Stiffness, and improved Processability. With a Glass Transition Temperature of 217°C, ULTEM™ 2210R PEI Resin maintains Structural Integrity under Elevated Thermal Conditions while supporting efficient Molding Performance.

Enhanced Flow Characteristics allow ULTEM™ 2210R PEI Resin to enable smoother Mold Filling and stable Processing Behavior, particularly for Components with Complex Geometries or Fine Features. This improved Flow Performance supports consistent Part Formation while preserving Reinforced Mechanical Strength and Dimensional Control.

Within the same Material Family, ULTEM™ 2210R PEI Resin serves as a General-Purpose Grade focused on balanced Mechanical Performance and Processing Efficiency. Compared to Alternative Grades with Regulatory Focus such as Food Contact Compliance, ULTEM™ 2210R PEI Resin is positioned for Applications where consistent Strength, Stability, and Manufacturing Reliability remain Primary Requirements.

The Glass Fiber Reinforcement provides enhanced Dimensional Stability, allowing Components to retain Shape under Mechanical Stress and Long-Term Use Conditions. This Structural Advantage ensures reliable Performance in Precision Engineering Applications where Tight Tolerances and Load Resistance are essential.

Predictable Processing Characteristics contribute to improved Production Efficiency, as ULTEM™ 2210R PEI Resin enables reduced Cycle Variability and better Repeatability across Manufacturing Runs. This Processing Consistency supports higher Part Quality and lower Defect Rates in High-Volume Production Environments.

In addition to Mechanical Performance, ULTEM™ 2210R PEI Resin offers strong Chemical Resistance, allowing exposure to Industrial Fluids and Cleaning Agents without compromising Material Integrity. Inherent Flame Retardant Properties enable UL94 V0 Classification from 0.41 mm to 3.00 mm, supporting safe use in Applications requiring Flame Resistance. ULTEM™ 2210R PEI Resin is also RoHS Compliant, supporting Environmentally Responsible Material Selection.

Supplied in Opaque Color Options, ULTEM™ 2210R PEI Resin is suitable for Applications where Transparency is not required but Structural Reliability is critical. Typical Applications include Structural Housings, Electronic Components, and Industrial Equipment Parts requiring High Strength and Thermal Resistance.

ULTEM™ 2210R PEI Resin provides a dependable combination of improved Flow, Reinforced Mechanical Properties, and consistent Processing Performance. With High Heat Resistance, Flame Retardant Capability, Chemical Durability, and Regulatory Compliance, ULTEM™ 2210R PEI Resin supports a wide range of General Engineering and Industrial Applications.

Notes:

ULTEM™ 2210R PEI Resin
20% Glass Reinforced
Added Mold Release
UL94 Rated
RoHS Compliant

ULTEM™ 2210R PEI Resin has 0.30 ~ 0.50 Shrinkage, Flow, 3.2 mm. %

Material HDT, 1.82 MPa, ASTM A648, °C

6.4 mm, unannealed 211

Vicat Softening Temperature Rate

Vicat Softening Temperature rate , B50 = 225

Material MFI / Melt Flow Rate

Melt flow Rate, 337°C/6.6 kgf = 9

Material Melt Volume Rate, MVR

N/a

Material Flexural Modulus

6500

ULTEM™ 2210R are UL94 - V0, 0.41 mm ~ 3.00 mm Rated

ULTEM Main Page

Disclaimer

Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021

SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.