ULTEM™ 2310R with 30% Glass Reinforced PEI Resin. Added Mold Release

Greater Rigidity. Improved Dimensional Stability and Improved Flow

ULTEM™ 2310R PEI Resin is engineered to simplify Molding of highly Reinforced Parts without Sacrificing Structural Performance. This 30% Glass Fiber Reinforced Polyetherimide introduces improved Flow and Built in Mold Release, making High Stiffness components easier to produce at consistent Quality.

The material is supplied in Opaque Form, supporting consistent Part appearance across production Runs.

ULTEM™ 2310R PEI Resin reduces Resistance during Molding. The improved Flow allows material to Fill Complex Geometries more effectively, even with High Glass Loading. at the Same time, the integrated Mold Release feature helps Parts Eject more cleanly, reducing Sticking and minimizing Cycle Interruptions.

Despite the Processing advantages, ULTEM™ 2310R PEI Resin maintains Strong Structural Performance. The Glass Reinforcement provides High Stiffness, supporting Parts that must resist deformation under Load. Dimensional stability remains consistent, especially in applications that require Tight Tolerances.

ULTEM™ 2310R PEI Resin operates with a Glass Transition Temperature of approximately 217 °C, allowing components to perform reliably in Elevated Temperature Environments without Loss of Mechanical Strength.

Functionally, ULTEM™ 2310R PEI Resin bridges the Gap between High Reinforcement Performance and manufacturing Efficiency. It support production where Structure Matters, while reducing Challenges typically associated with Heavily Filled Resins.

From a Safety Standpoint, ULTEM™ 2310R PEI Resin meets UL94 V0, 0.25 mm ~ 3.00 mm Rated, enabling use in applications requiring Flame Resistance at Thin Sections.

ULTEM™ 2310R PEI Resin meets Environmental Requirements through RoHS Compliance, supporting Responsible use in Advanced Engineering applications.

Notes:

ULTEM™ 2310R PEI Resin
30% Glass Reinforced
Improved Flow
Easy Release
UL94 Rated
RoHS Compliant

ULTEM™ 2310R PEI Resin has 0.20 ~ 0.40 Shrinkage, Flow, 3.2 mm. %

Material HDT, 1.82 MPa, ASTM A648, °C

3.2 mm, unannealed 211

Vicat Softening Temperature Rate

Vicat Softening Temperature rate , B50 = 213

Material MFI / Melt Flow Rate

Melt flow Rate, 337°C/6.6 kgf = 7.6

Material Melt Volume Rate, MVR

Melt Volume Rate, 360°C/5.0 kgf = 8

Material Flexural Modulus

9600

ULTEM™ 2310R are UL94 - V0, 0.25 mm ~ 3.00 mm Rated

ULTEM Main Page

Disclaimer

Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021

SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.