BRINGING THE RIGHT MATERIAL & BEST SERVICES IN SOUTH EAST ASIA
Thailand Office : +66 64 586 6450
Malaysia Office : +60 12 956 4808
Indonesia Office : +62 818 0402 0119
Vietnam Office : +84 934 036 679
Philippines Office : +63 917 567 4188
India Office : +91 961 999 5685
ULTEM™ 3310TD Mineral Filled Polyetherimide (PEI) Resin. Enhanced Flow
Unique combination of Low CTE and High near Infrared Transparency.
ULTEM™ 3310TD PEI Resin is a High-Performance Engineering Thermoplastic reinforced with Glass Fiber and Mineral Fillers, designed for Applications requiring High Flow, Low CTE, and Optical Precision in Near Infrared Systems. ULTEM™ 3310TD PEI Resin is specifically engineered for Optical Transceiver Components such as Collimator Lenses in Fiber Optic Systems, where Dimensional Control and Optical Performance remain Critical Requirements.
The Hybrid Reinforcement System in ULTEM™ 3310TD PEI Resin provides enhanced Dimensional Stability, High Stiffness, and reduced Thermal Expansion, allowing Components to maintain Accurate Optical Alignment under varying Temperature Conditions. The material exhibits a Low Coefficient of Thermal Expansion of approximately 38 Ppm/°C, supporting Stability in Temperature-Sensitive Environments and Precision Optical Applications.
ULTEM™ 3310TD PEI Resin delivers Near Infrared Transparency with High Refractive Index, enabling efficient Light Transmission and reliable Optical Performance in Single-Mode Fiber Optic Systems. This capability allows ULTEM™ 3310TD PEI Resin to support Miniaturized Optical Components where Precision, Light Control, and Signal Accuracy are Essential Performance Factors.
High Flow Characteristics enable ULTEM™ 3310TD PEI Resin to support efficient Micro-Molding and High-Volume Production of Complex Geometries while maintaining Fine Feature Definition. This combination allows greater Design Flexibility and Manufacturing Efficiency without compromising Optical or Structural Performance.
ULTEM™ 3310TD PEI Resin maintains High Heat Resistance and Mechanical Strength, ensuring Long-Term Performance in demanding Thermal and Operational Conditions. The material also supports Weight Reduction while maintaining Structural Integrity, making ULTEM™ 3310TD PEI Resin suitable for Compact and High-Efficiency System Designs.
As a Transparent Mineral-Filled Formulation, ULTEM™ 3310TD PEI Resin is optimized for Optical Applications where both Processability and Performance must be balanced. Typical Applications for ULTEM™ 3310TD PEI Resin include Optical Transceivers, Collimator Lenses, Fiber Optic Components, and Precision Optical Systems requiring Low CTE, NIR Transparency, and consistent Dimensional Stability.
ULTEM™ 3310TD PEI Resin is not UL Rated, as it is optimized for Optical Precision and Material Performance rather than Flame Classification. ULTEM™ 3310TD PEI Resin is also RoHS Compliant, supporting Environmentally Responsible Material Selection while delivering High-Precision Optical and Structural Performance.
Notes:
ULTEM™ 3310TD Polyetherimide (PEI) Resin
Mineral Filled
Enhanced Flow
High Near Infrared Transparency
RoHS Compliant
ULTEM™ 3310TD PEI Resin has 0.58 Shrinkage, Flow, 3.2 mm. %
Material HDT, 1.82 MPa, ASTM A648, °C
6.4 mm, unannealed 196
Vicat Softening Temperature Rate
Vicat Softening Temperature rate , B50 = 211
Material MFI / Melt Flow Rate
Melt flow Rate, 337°C/6.7 kgf = 10.3
Material Melt Volume Rate, MVR
Melt Volume Rate, 337°C/6.7 kgf = 6.84
Material Flexural Modulus
4900
ULTEM™ 3310TD are Non UL Rated
Disclaimer
Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021
SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.