ULTEM™ 3452. 45% Glass & Mineral Reinforced PEI Resin. Enhanced Flow

Greater Rigidity. Improved Dimensional Stability vs ULTEM 2000 Series

ULTEM™ 3452 PEI Resin is a 45% Glass & Mineral Reinforced with Enhanced Flow Resin for Wide Applications

It's Available in Opaque Color & Contained Reinforced

ULTEM 3452 Resin has Enhanced Dimensional Stability, Non FR Modifiers & Higher Strength Charateristics

It is from ULTEM™ 3000 Family Series, An Glass and Mineral Reinforced Amorphous Thermoplastic Polyetherimide (PEI) Materials offering Better Strength and Improved Dimensional Stability vs ULTEM™ 2000 Series

ULTEM™ Polyetherimide or PEI Resin offers

- Remarkable Strength and Stiffness offering Outstanding Strength among the Available Alternatives, with Predictable Stiffness and strength up to 200° Celsius. Unfilled, Transparent Grades are Equal in Strength to other Thermoplastics with Opacifying Fillers.

- Long-Term Heat Resistance, thus Achieving Excellent Stability of Mechanical and Physical Properties at Elevated Temperatures due to High Glass Transition Temperature of 217 °C. Available Relative Thermal Indices (RTI) up to 180° Celsius

- High Dimensional Stability offers Predictability over a Wide Temperature Range. Filled Grades offer Exceptionally High Tolerance Dimensional Capabilities.

- Environmental Stress & Cracking Resistance. Unlike Most Other Amorphous Thermoplastics, Ultem Resins Retain Strength and Resist Stress Cracking when Exposed to Automotive and Aircraft Fluids, Aliphatic Hydrocarbons, Alcohols, Acids, and Weak Aqueous Solutions.

- Flammability, Smoke Generation, and Toxicity Inherent Flame Resistance without Additives in Most Grades. Exceptionally Difficult to Ignite, with A Limiting Oxygen Index (LOI) Of 47%. Meeting UL94 V0 Specifications in Sections As Thin As 0.41 mm. Generates Extremely Low Smoke per NBS Smoke Evolution Test, with Products of Combustion No More Toxic than Those of Wood.

- Good Processability. Can Be Extruded, Thermoformed, Extrusion, Blow Molded and Injection Molded. Good Flow Ability allows Long Flow Lengths Down to 0.2 mm Thick Using Conventional Injection Molding Equipment.

ULTEM 3452 PEI has 0.15 ~ 0.25 Shrinkage, Flow, 3.2 mm. %

Material HDT, 1.82 MPa, ASTM A648, °C

6.4 mm, unannealed 212

Vicat Softening Temperature Rate

N/A

Material MFI / Melt Flow Rate

Melt Flow Rate, 337°C/6.6 kgf = 4.6

Material Melt Volume Rate, MVR

N/A

Material Flexural Modulus

12000

ULTEM™ 3452 are UL94 - V0, 0.77 mm ~ 3.00 mm Rated

ULTEM Main Page

Disclaimer

Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021

SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.