ULTEM™ AR9200 20% Glass Reinforced FAR Certified Standard Flow PEI Resin

FAR 25.853 and OSU 65/65 Compliance for Advanced Fire Safety Requirements

ULTEM™ AR9200 PEI Resin is developed for Environments where material Performance is defined by Safety Standards. This 20% Glass Reinforced Polyetherimide meets Stringent Aerospace Requirements for Flame, Smoke, and Toxicity, making it suitable for applications where Compliance is critical.

the Advance ULTEM™ AR9200 PEI Resin is certified to FAR 25.853, Along with OSU 65/65 Testing, addressing Flame Spread, Heat Release, and Smoke Generation. The material also Demonstrates Low Toxicity during Combustion, supporting use in Enclosed or Passenger accessible systems where Safety Performance cannot be Compromised.

ULTEM™ AR9200 PEI Resin delivers Dependable Stiffness and Rigidity, allowing components to maintain Integrity under Load while resisting deformation over time. This makes it suitable for Parts that must combine Compliance with Mechanical Durability.

Processing follows a standard Flow Profile, enabling consistent Molding without introducing Complexity. ULTEM™ AR9200 PEI Resin balances Ease of manufacturing with the Performance Demands of Aerospace applications.

ULTEM™ AR9200 PEI Resin operates with a Glass Transition Temperature Around 217 °C, allowing reliable Performance in Elevated Temperature Environments without Loss of Structural Strength.

Fire Performance Extends beyond Certification. The material is designed to Minimize Smoke Density and Flame Propagation, supporting System Level Safety in Aircraft Interiors and Transportation applications.

Typical uses include Aerospace Interior components, Seating Structures, Panel Systems, Enclosures, and Electrical Assemblies, where Flame, Smoke, Toxicity, and Mechanical Strength must all meet Regulatory Standards.

Environmental Expectations are addressed through RoHS Compliance and ECO Conformance, supporting Responsible material Integration alongside High Safety Performance.

Notes:

ULTEM™ AR9200 PEI Resin
20% Glass Fiber Reinforced
meets FAR 25.853 and OSU 65/65
RoHS Compliant

ULTEM™ AR9200 PEI Resin has 0.30 ~ 0.50 Shrinkage, Flow, 3.2 mm. %

Material HDT, 1.82 MPa, ASTM A648, °C

6.4 mm, unannealed 211

Vicat Softening Temperature Rate

N/a

Material MFI / Melt Flow Rate

Melt flow Rate, 337°C/6.6 kgf = 5.7

Material Melt Volume Rate, MVR

N/a

Material Flexural Modulus

7230 ( 2.6 mm/min, 100 mm span )

ULTEM™ AR9200 are Non UL Rated

ULTEM Main Page

Disclaimer

Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021

SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.