ULTEM™ AUT200G6 High Flow, 30% Glass Reinforced PEI Automotive Resin

Developed for Metalizing and High Reflective Surface Requirement

ULTEM™ AUT200G6 PEI Resin Extends the Performance of Optical Materials into Structural Territory. developed for Automotive Lighting Systems, this 30% Glass Reinforced Polyetherimide Blend is designed to Support components that must maintain Shape while still delivering controlled Reflective Performance.

this PEI Resin adds Rigidity where Optical Plastics typically Fall Short. The 30% Glass Reinforcement increases Stiffness, allowing Larger or more Complex Lighting Parts to resist deformation under Thermal and Mechanical Stress. This is especially important in Assemblies where alignment directly affects Light Output.

ULTEM™ AUT200G6 PEI Resin features enhanced Flow, enabling the material to Fill Detailed Molds with better consistency. This support precise Geometries required for Reflector Housings and Structural Optical components.

Surface Performance is engineered for Metallization. ULTEM™ AUT200G6 PEI Resin provides a Stable Substrate for Reflective Coatings, supporting High Reflectivity Finishes used in Automotive Lighting Systems. This allows Structural Parts to Double as Functional Optical Elements.

ULTEM™ AUT200G6 PEI Resin Operates with a Glass Transition Temperature of approximately 217 °C, maintaining Dimensional stability even under continuous Heat from Light Sources and Engine Environments.

the material is supplied in Opaque Colors, suitable for Structural and Reflective applications where Transparency is not required.

Typical uses include Automotive Reflectors, Lighting Housings, Structural supports, and Metallized components, where Stiffness, Heat Resistance, and Reflective Performance must Work Together in a single material System.

ULTEM™ AUT200G6 PEI Resin meets Environmental Expectations through RoHS alignment, supporting Responsible use alongside High Performance Engineering Requirements.

Notes:

ULTEM™ AUT200G6 PEI Automotive Resin
30% Glass Reinforced
High Flow
Developed for Metalizing and High Reflective Surface
RoHS Compliant

ULTEM™ AUT200G6 PEI Resin has 0.20 ~ 0.40 Shrinkage, Flow, 3.2 mm. %

Material HDT, 1.82 MPa, ASTM A648, °C

6.4 mm, unannealed 210

Vicat Softening Temperature Rate

Vicat Softening Temperature rate , B50 = 213

Material MFI / Melt Flow Rate

Melt flow Rate, 337°C/6.6 kgf = 7.6

Material Melt Volume Rate, MVR

Melt Volume Rate, 360°C/5.0 kgf = 8

Material Flexural Modulus

8500

ULTEM™ AUT200G6 are Non UL Rated

ULTEM Main Page

Disclaimer

Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021

SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.