ULTEM™ PW2400 40% Glass Reinforced FDA Water Potable PEI Resin

KTW-BWGL, WRAS, ACS, NSF 61, W270, EU, US Food Contact Certified

ULTEM™ PW2400 PEI Resin is a 40% Glass Reinforced Resin for Potable Water Applications

It's Available in Transparent Amber or Black Color

ULTEM PW2400 Resin offer Standard Flow & Good Hydrolytic Stability

It is from the ULTEM™ PW, An Amorphous Thermoplastic Polyetherimide (PEI) Materials with Potable Water Certifications, NSF61, REG4, KTW-BWGL, W270, ACS, WRAS. These Series also have Food Contact Compliance (FDA, CN, EC). Ther offers Excellent Mechanical, and Dimensional Properties up to High Temperatures and Under Wet Conditions.

ULTEM™ Polyetherimide or PEI Resin offers

- Remarkable Strength and Stiffness offering Outstanding Strength among the Available Alternatives, with Predictable Stiffness and strength up to 200° Celsius. Unfilled, Transparent Grades are Equal in Strength to other Thermoplastics with Opacifying Fillers.

- Long-Term Heat Resistance, thus Achieving Excellent Stability of Mechanical and Physical Properties at Elevated Temperatures due to High Glass Transition Temperature of 217 °C. Available Relative Thermal Indices (RTI) up to 180° Celsius

- High Dimensional Stability offers Predictability over a Wide Temperature Range. Filled Grades offer Exceptionally High Tolerance Dimensional Capabilities.

- Environmental Stress & Cracking Resistance. Unlike Most Other Amorphous Thermoplastics, Ultem Resins Retain Strength and Resist Stress Cracking when Exposed to Automotive and Aircraft Fluids, Aliphatic Hydrocarbons, Alcohols, Acids, and Weak Aqueous Solutions.

- Flammability, Smoke Generation, and Toxicity Inherent Flame Resistance without Additives in Most Grades. Exceptionally Difficult to Ignite, with A Limiting Oxygen Index (LOI) Of 47%. Meeting UL94 V0 Specifications in Sections As Thin As 0.41 mm. Generates Extremely Low Smoke per NBS Smoke Evolution Test, with Products of Combustion No More Toxic than Those of Wood.

- Good Processability. Can Be Extruded, Thermoformed, Extrusion, Blow Molded and Injection Molded. Good Flow Ability allows Long Flow Lengths Down to 0.2 mm Thick Using Conventional Injection Molding Equipment.

ULTEM PW2400 PEI has 0.10 ~ 0.30 Shrinkage, Flow, 3.2 mm. %

Material HDT, 1.82 MPa, ASTM A648, °C

N/A

Vicat Softening Temperature Rate

Vicat Softening Temperature rate , B50 = 217

Material MFI / Melt Flow Rate

N/A

Material Melt Volume Rate, MVR

Melt Volume Rate, 360°C/5.0 kgf = 5

Material Flexural Modulus

10000

ULTEM™ PW2400 are UL94 - V0, 0.25 mm ~ 3.00 mm Rated

ULTEM Main Page

Disclaimer

Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021

SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.