XENOY™ X5630Q Advanced PC/PET Resin. 19% Mineral Filled Reinforced

Low CTE, Low Shrinkage & Good Dimension Stability. Paint applications

XENOY™ X5630Q PC/PET Resin is engineered for Automotive Exterior components that demand enhanced Dimensional Accuracy and Structural Consistency under Paint Processing Conditions. It is developed as a Higher-performance Variant within Mineral-Filled Systems, supporting Tighter Tolerances and improved Stability.
the formulation incorporates 19% Mineral Reinforcement, Increasing Stiffness and enabling Greater Resistance to Dimensional change compared to Lower-Filled Alternatives. This Higher Reinforcement Level provides improved Control over deformation, particularly in Large or Precision Exterior Parts.
XENOY™ X5630Q PC/PET Resin delivers a Low Coefficient of Thermal Expansion (CTE), ensuring that Parts remain stable during Thermal Cycles such as Paint Curing and Environmental exposure. This Minimizes Risks of Warpage, Misalignment, or Surface Distortion in Painted Assemblies.
the material also Exhibits Low Shrinkage behaviour, allowing Parts to maintain Accurate Geometry during Molding and Cooling. This contributes to improved Assembly Fit and Consistency across production Batches.
XENOY™ X5630Q PC/PET Resin provides High Heat Resistance, enabling it to withstand the elevated Temperatures Associated with Automotive Paint Systems while preserving Dimensional Integrity and Surface Readiness.
in addition to Stiffness, the Resin maintains balanced Impact Strength and Chemical Resistance, ensuring Durability in real-World Conditions where exposure to Automotive Fluids and Environmental Stress is expected.
XENOY™ X5630Q PC/PET Resin is not UL94 Rated, as its formulation is optimized for Painted Surface Stability, Dimensional Precision, and Thermal performance, raTher than Flame-Retardant applications.
XENOY™ X5630Q PC/PET Resin is ideally suited for Automotive Body Panels, Exterior Trims, Housings, and Painted Structural components, where Low CTE, High Heat Resistance, and precise Dimensional Control are Essential.
XENOY™ X5630Q PC/PET Resin is RoHS Compliant, supporting Responsible material selection while delivering enhanced Dimensional Precision for Advanced Painted applications.

XENOY X5630Q PC/PET has 0.5 ~ 0.7 Shrinkage, flow, 3.2 mm. %

Material HDT, 1.82 MPa, ASTM A648, °C

N/a

Vicat Softening Temperature Rate

SABIC XENOY™ X5630Q Vicat Softening Temperature rate , B50 = 137

Material MFI / Melt Flow Rate

Melt flow Rate, 265°C/5.0 kgf = 20

Material Melt Volume Rate, MVR

Melt Volume Rate, 265°C/5.0 kgf = 16

Material Flexural Modulus

XENOY™ X5630Q Flexural Modulus, ISO 178, 2 mm/min = 4100 Mpa

XENOY™ X5630Q are Non UL94 Rated

XENOY Main Page

Disclaimer

Any sale by SABIC, Its Subsidiaries and Affiliates (each a “Seller”), is Made Exclusively under Seller’s Standard Conditions of Sale (available upon request) unless Agreed Otherwise in Writing and Signed on behalf of the Seller. While the Information Contained herein is given in Good Faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY APPLICATION. Each Customer must Determine the Suitability of Seller Materials for the Customer’s Particular Use through Appropriate Testing and Analysis. No Statement by Seller Concerning a Possible Use of any Product, Service or Design is Intended, or should be Construed, to grant any License under any Patent or other Intellectual Property Right. © 2021

SABIC Innovative Plastics is a Trademark of SABIC Holding Europe BV * Cycolac, Cycoloy, Lexan, Noryl, Ultem, Valox and Visualfx are Trademarks of SABIC Innovative Plastics IP BV © Copyright 2008 SABIC Innovative Plastics IP BV. All rights reserved.